توضیحات محصول
عایق کاتالیستی دو جزیی E200
ELECTROLAC E200 CLیک محصول دو جزئی حلال پایه است که براساس رزین های مدیفای شده تولید میگردد. کلاس حرارتی این محصول در گروه H(180 درجه سانتیگراد) و برای عایق کاری الکتروموتورهای ولتاژ بالا و عایق کپسوله ساز طراحی گردیده است. سختی ، مقاومت الکتریکی و حرارتی و همچنین مقاومت به رطوبت و مواد شیمیایی از ویژگیهای بارز این محصول میباشد .
جهت اعمال و کاربردELECTROLAC E 200 CL از رقیق کننده SOLVLAC S 400 استفاده گردد و میزان ترکیب رقیق کننده بسته به روش کاربرد-قلم مو ، اسپری هوا و دمای محیط بین 20 تا 40 درصد متفاوت است . این محصول را دور از نور مستقیم آفتاب و شعله و در شرایط استاندارد انبار میتوان بمدت یکسال نگهداری نمود .
نسبت اختلاط 2 به 1 از نظر وزنی است (دو قسمت بخش رزین و یک قسمت بخش هاردنرکه بخش هاردنر را به آرامی به رزین اضافه و بخوبی همگن نمایید. با توجه محدودیت زمان محمل پس از اختلاط که 4 ساعت در دمای 20 درجه سانتیگراد است هر شیفت کاری بر اساس نیاز دو جزء را مخلوط نمایید.
Product description
ELECTROLAC E 200 CL designates a solvent-based, good viscosity, special based trickle resin. Furthermore, this combination is noted for its very good penetration, especially for Insulation of high voltage electric motors and insulation of capsule maker.
Polymerization is initiated by mixing the two components and under the effect of heat proceeds as a rapid chain-reaction until a three-dimensionally cross-linked, duroplastic cured material is produced.
Areas of application
Preferred applications for ELECTROLAC E 200 CL
- Induction Furnace industry
- Repair shops
- Windings of machines with high chemical requirements
- Electronic device
Properties of cured material
After curing there is a hard cured material, which is noted for its exceptional adhesion to various materials. The cured material also displays very good resistance to tropical influences, solvents, weak lyes-alkalies as well as oil and allows impregnated objects to be used even under extreme conditions.
The high bonding strength of this combination imparts good mechanical stability to the impregnated windings.
ELECTROLAC E200 CL due to its high bond strength offers increased resistance to centrifugal forces for large size armatures, thus preventing wire shifting & improving its life.
Application guide
ELECTROLAC E 200 CL in combination with hardener can be processed in all conventional trickling plants.
Gelling and curing usually occurs in a circulating air oven or by current heating under rotation.
The rate of mixing ELECTROLAC E 200 CL 2:1( is two part of resin by weight and one part of hardener),according to a principle, stir tow part separately and then add the hardener to resin slowly. Because of limit pot-life please mix the volume which you need to use. The pot-life is 4 hours (20°)
Uncured resin can be easily cleaned by washing with hot detergent solution, acetone or Thinner. It is difficult to remove cured resin and for this reason tools and containers contaminated with resin + hardener mixture should be cleaned immediately after use.
Application method
Preferred applications for ELECTROLAC E 200 CL
The recommendation of thinning is 20 to 40 percent SOLVLAC S400
Storage and stability
Under appropriate storage conditions, protected from humidity and solar radiations, ELECTROLAC E 200 CL and reducer SOLVAC S 400 can be stored in unopened container at 20-30 °C for 12 months.